Koxx_TryAll

Dont really see the point in that stupid remark. but i spose its normal for a sad act like you!

Sorry to be a willy. But as a cat lover i dont really think thats very funny to be honest! Nick

A good small reliable car would be a ford fiesta. But it you want a really good reliable care. either get a skoda or a volvo!

Hes one of them cowboy mechanics. The ones that just bung things together and as long as it works for a while its ok lol!

So's the carp background! And the clock with the real time!

Just to spread the word about the new msn messenger Msn 7.5 so for all you msn lovers heres the link! Msn 7.5 Post your opinions!

haha

You see. As i'm a mechanic aswell it seems i know alot more about it then you do. Also theres more reasons. As you increase revs you may get popping and perhaps in a darkened garage or at night a blue flame shooting out of a pipe on the front of the engine around the exhaust pipes. The flame if any will come from around the clamp. It may not have been assembled correctly at the Factory, or it might just have got tired. It can also make it LOOK like a weeping head gasket, because of the spooge that comes out, so don’t go replacing your head Gasket Until you’re sure.! Also, this junction is right below the temp sensor that turns on the fan. The hot air blowing out of there Can heat up the thermostat and fan sensor, turning the fan on prematurely. And when the fan comes on, it will blow the hot exhaust gasses on your leg. Thank you

A leak at the exhaust flange gasket is often caused by improper torquing. Too little torque and the connection loosens. Too much torque and the gasket will bow slightly — again allowing exhaust gases to leak. If left uncorrected, erosion of the aluminum cylinder head material will occur quite quickly. A loss of material amounting to only a few thousandths of an inch could be enough to make the cylinder unusable. Therefore, correcting the problem quickly is essential. If the aluminum cylinder head material has already eroded as the result of an exhaust gas leak, repair is sometimes possible. This cannot be done by hand. Studs must be removed and the damaged surface refinished by use of a milling operation. No more than twenty thousandths of an inch may be removed. Should it be necessary to remove more than twenty thousandths of an inch to obtain a true surface, the cylinder should be replaced.

It's going to be... Ive got one now so can you please shut up!

It will f**k your engine. When theres no gasket on the exhaust manifould it will f**k it!

Ask a Mechanic. You'll see. Why the f**k do you think they use a gasket there anyway you tard!

No chance that you can make one mate because it will just manage to suck up air into the engine then i end up without a car. So i'd rarther have the part then reck my car! And this is chit chat btw. we can post what we want in here! Anyway People Chears for your help. Got one now!

Does anyone know where i can get an exhaust Flange gasket from for a Volvo 850 GLT Estate as i just dont seem to be able to find one anywhere! Like this one! Chears.

Take it apart. Clean all the bearings and then grease them!

Well i'd go for a Shimano Rx100 Mech. Well that's what i use. I Made my own single speed kit. You should do the same. Nick

They Might be Just polished underneath because its white under the black. But that may be undercoat. Or the white could be the colour :(

M-a-d Forks are Alloy.

I got these Forks with a Trials bike i bought ages ago off Ebay and i just have no idea what they are. All i know is that there Steel with a Disc Mount. Can you tell me what they are?? Chears Sorry about the Bold Tyre i'm getting new one. And sorry about the Pictures they have been taken with a camera off a phone!

Link To A Trials Bike On Ebay! This bike looks cool!